KASSIE CUBE
Side table, 400 × 400 × 400 mm. 12 steps to build, then 5 more for what a second cube or the shelf can do.
Prototype draft: sizes are unverified until the prototype checks pass.
In the box
Every part has a small peel-off sticker with its code (PW1, SW2 …). Peel them off when you're done.
Hardware
You need
Every hole is already drilled and countersunk. No drill, no glue. About 20 minutes, one person.
Drag a picture to turn it; double-click puts it back. Printing uses the fixed views.
Build the side table
Lay a plain wall (PW1) flat on a soft, clean floor, inner face up (the face with the engraved line).
Lower slotted wall SW1 into one end: its fingers down into PW1's slots, rims level.
Lower slotted wall SW2 into the other end the same way.
Lower the second plain wall (PW2) onto the top, inner face down, fingers into the slots.
Press PW2 down. Drive the four 4 × 40 screws into the pre-drilled holes by hand, heads flush. Snug, not forced.
Turn the cube over and press PW1 home. Drive the other four 4 × 40 screws the same way.
Turn the cube rim-down. Screw plinth strips PL1 (cable notch out) and PL2 to the plain walls, in the pre-drilled holes.
Drop PL3 and PL4 in between them, ends in the rebates, and screw them on.
Stick a felt pad under each corner of the plinth.
Stand the cube up. Tilt the bottom (B) in, cable notch by PW1: push it into SW2's slot, drop it, slide it back.
Keep the two clips (U) safe in the hardware bag until you join a second cube; the lid's two small pockets are their parking spots.
Fit the lid thumb notch by PW1, small pockets underneath (it only stops this way round): push into SW2's slot, drop, slide back until it stops. Your side table is done.
Got a second cube?
Got a second cube? Stand them side by side, rims level. Tip them back, press two clips up into the pockets under the seam, stand them up: a coffee table.
Or stack them: lift one onto the other. Its plinth drops inside the lower rim, so it can't slide off. A tall side table.
Turn it into shelves
Shelves: take the lid out and lay the cube on its side on a wall with no screw heads, the bottom to the back.
Slide the lid in as a shelf: thumb notch to the front, pockets down. Deep edge into SW2's groove, drop the other edge, slide back, then forward to the stop.
Two on their sides: set the second beside the first, then press two clips into the back edges of the seam, from behind. Push them to the wall.
Every way to use your cubes
| Side table | 1 | Upright, lid on. This guide's build. |
| Blanket or toy box | 1 | Upright and closed. |
| Open shelf | 1 | On its side, the lid as its shelf (steps 15–16). |
| Coffee table | 2+ | Upright, side by side, clipped underneath (step 13). |
| Tall side table | 2 | Upright, one stacked on the other (step 14). |
| End-of-bed bench with a cubby | 3 | Two cubes upright, joined slotted wall to slotted wall (plain faces front and back, thumb notches to the front), clipped underneath, lids on top: storage, not seats. The end cube on its side, open to the front, its lid its shelf, for shoes or books: its solid top is the seat, for one adult, once its seat test is passed. The end cube can't clip to the others (its clip pockets face back), so push the bench against the bed. |
| Tall laundry box | 2 | Stacked, with the lower lid and the upper bottom out: one tall bin with a lid on top. |
| Shoe rack | 2–4+ | On their sides, open and closed, clipped at the back (step 17). Open cubes' lids are their shelves. |
| Bookshelf or display | 2–3+ | On their sides, stacked and clipped at the back. |
| TV cabinet | 3 | On their sides in a row, clipped at the back; one open for devices, its lid its shelf. Cables out through the back's cable notch. |
Good to know
- Open the lid by pushing it toward the deep side (SW2) about 5 mm with a thumb in the notch, then tilt and lift.
- Don't lift or carry a cube by its lid. Take cubes apart before you move them.
- Drive screws by hand (or a drill-driver on its lowest clutch): the holes are pre-drilled and strip if forced.
- On its side, a cube always lies on a wall with no screw heads.
- Over 800 mm high (three cubes or more), screw the top row to the wall through its plinth.
- Sit only on the cubby cube of the end-of-bed bench (the one on its side), one adult, once its seat test is passed. The lids are not seats. Never stand on a cube.
- Indoors only. Wipe with a damp cloth; re-oil a worn top with a hardwax oil.
- To take a cube flat: clips, lid and bottom out; unscrew the short plinth strips, then the long ones, then the corners.